|Topic Review (Newest First)|
|04-28-2019 08:15 AM|
Do a compression check and you may find your answer to the oil burning. Low compression in one or two cylinders indicates a tear down.
Compression check cheapest and most reliable source of info.
Check with your local jobber outlet, they often have tool rental plans that may not cost you for this diagnostic process.
|06-12-2009 08:51 AM|
|kingnutin||Hang on I have to change my underwear... Okay, yeah that would be nice. Unfortunately a bottle of crap is about as far as my budget will take me right now. My goal is to eventually swap the engine and tranny as a unit to something far more modern, but that would cost me as much as a new car that I can't afford either...|
|06-09-2009 08:55 AM|
|kingnutin||So basically, the only fix is either a rebuild or a new motor. That's what I needed to figure out.|
|06-08-2009 10:21 AM|
|Buffman||it's not going to fill in any damage in the cylinder walls.|
|06-04-2009 03:17 PM|
|kingnutin||So... I don't have any sludge, never have. What I do have is oil burning, low power, and shitty mileage. That was the reason I was looking at restore, since it claims to fill in scratches and what-nots in the cylinder walls. My biggest concern is what that means it will do to other parts.|
|06-04-2009 03:08 PM|
In general vacuum lines do not need to be cleaned out. I have never found a carbon plugged vacuum line yet.
Now there is a combustion chamber cleaner that does get pulled into the vacuum lines and it is supposed to clean the carbon off the inside of the chamber and makes a lot of white smoke. I have tried it in my van, not sure if it really helped or not. I used it when I replaced the timing chain a month ago.
|06-04-2009 01:20 PM|
Originally Posted by Buffman View Post
And I hear some local garages wanting to shoot alcohol into my vacuum lines to "clean them out". I've seen them do this to other cars and it just creates a TON of white exhaust. That can't be good. Or can it? Is it necessary to clean vacuum lines?
|06-04-2009 09:23 AM|
Originally Posted by cbmikey View Post
Some engines are known sludgers. driving habits don't help situations.
If you want experience. I used to put a quart of rislone in my 89 caprice with 190K miles at the time of ownership (sold it with 226K) at the recommendation of my dad who also thinks Bahr-Dal(sp) works great too. I think afer a year of ownership I stopped using it. When I changed the valve cover gaskets, you wouldn't believe all the caked up sludge I found in the heads. Rislone certainly didn't clean anything up.
|06-03-2009 12:47 PM|
|kingnutin||Valve job was already done, I believe its rings, which is why I was considering that treatment. Basically, if I can stop burning as much oil and get some compression back I will be happy. At least until I can afford to either rebuild or replace the engine.|
|06-03-2009 10:21 AM|
Originally Posted by Buffman View Post
My old man out-law swears by it and is much older than I am. He's been a gearhead far longer than I and likely many people here. (he's turning 60 this fall)
I know you like numbers and hard data, (NTTAWWT) but I like recommendations of people who know more than I do. Just my 2 cents.
EDIT: I have used Restore before. I used it on my '79 Monte (before I knew better) because I was getting a wee little bit of blowby. It did cure the blowby, but it also plugged up the oil drain holes in the heads. If you need a temporary cheap fix, go for it, but still start saving up for an upper engine rebuild.
|06-02-2009 10:14 PM|
|Buffman||The only oil "additive" worthwile is www.auto-rx.com restore is worthless, rislone is, and zmax is.|
|06-02-2009 08:22 PM|
If your motor uses that much oil then don't bother trying any type of snake oil additive. On another web-site Z-MAZ is said to be nothing more than a fake. It's just mineral oil. Your better off considering a valve job.
|05-19-2009 04:13 PM|
|kingnutin||Damn, they should really use that in their marketing! My case is a little different than most though, since I recently did a top end rebuild. At least I hope that makes a difference...|
|05-19-2009 01:57 PM|
|kingnutin||Thats all I ask. I just want to know what others have experienced, instead of reading a bunch of made-up testimonials on a products website. Thanks.|
|05-19-2009 01:30 PM|
|COLD STEEL||it acted as some sort of sealer type additive. Which made for less oil loss and slightly better fuel mileage. Again its an additive, it will not do much but if your to that point, anything is better than nothing as long as you think it over. I am not telling you to use it or buy that, just giving you a little feedback on what I noticed on my junker years ago.|
|This thread has more than 15 replies. Click here to review the whole thread.|